Home > Socket Error > Winsock Error Code 10040

Winsock Error Code 10040

Contents

WSAEAFNOSUPPORT 10047 Address family not supported by protocol family. The socket is marked as non-blocking (non-blocking operation mode), and the requested operation is not complete at this time. The call has been canceled. No connection could be made because the target machine actively refused it. Source

WSAEUSERS 10068 Too many users. Request refused: name server refuses to satisfy your query for policy reasons. WinSock description: No error. Normally results from an attempt to bind() to an address that is not valid for the local machine.

Socket Error 10054

WinSock description: a quick comparison to the Berkeley counterpart, and a long description of WinSock error. Note that the v1.1 WinSock specification does not explicitly state that this error occurs if the value you request is larger than the WSAData.iMaxUdpDg returned from WSAStartup(). Generically, the error means the network system has run out of socket handles. You can verify that the remote system is rejecting your connection attempt by checking the network statistics locally.

When bind is called with a wildcard address (involving ADDR_ANY), a WSAEADDRINUSE error could be delayed until the specific address is committed. WinSock functions: getsockopt(), setsockopt() Additional functions: Bad IP headers can cause routers and remote hosts to issue ICMP "parameter problem" messages, which result in a ENOPROTOOPT error on Berkeley-derived systems. WinSock description: Same as Berkeley. Socket Error 10054 Connection Reset By Peer Error Definition Errno WSAEWOULDBLOCK 10035 WSAEINPROGRESS 10036 WSAEALREADY 10037 WSAENOTSOCK 10038 WSAEDESTADDRREQ 10039 WSAEMSGSIZE 10040 WSAEPROTOTYPE 10041 WSAENOPROTOOPT 10042 WSAEPROTONOSUPPORT 10043 WSAESOCKTNOSUPPORT 10044 WSAEOPNOTSUPP 10045 WSAEPFNOSUPPORT 10046 WSAEAFNOSUPPORT 10047 WSAEADDRINUSE 10048

WSASYSNOTREADY (10091) Network subsystem is unavailable. Socket Error Codes Linux There are only a few possible causes for this error: you tried to connect to the wrong port. WinSock description: No equivalent. The name you have used is not an official hostname or alias.

I read the file into an array sendBuffer[14990] I have a corresponding recvBuffer[14990] I determined the max buffer size of my system(8192 bytes) by doing a getsockopt(). Socket Error 11004 WSAEDESTADDRREQ (10039) Destination address required. WSA_QOS_EFILTERSTYLE 11019 Invalid QoS filter style. Developer suggestions: Handle this as a non-fatal error.

Socket Error Codes Linux

Berkeley description: An operation was attempted on a non-blocking object that already had an operation in progress. See other suggestions under WSAECONNABORTED. Socket Error 10054 The WinSock implementation will not allow you to send after this. Socket Error 10053 Ping the remote host you were connected to.

WSAVERNOTSUPPORTED 10092 Winsock.dll version out of range. this contact form It could also occur if an application opens and closes sockets often, but doesn't properly close the sockets (so it leaves them open, as "orphans"). If there is more than one WINSOCK DLL on your system, be sure the first one in the path is appropriate for the network subsystem currently loaded. the WinSock implementation WSAENOTCONN (10057) Socket is not connected. Socket Error 10049

Specifically, the v1.1 Windows Sockets specification notes the domain name system (DNS) errors "FORMERR, REFUSED, and & NOTIMP. Join our community for more solutions or to ask questions. WSANOTINITIALISED 10093 Winsock not yet initialized. have a peek here WSAEOPNOTSUPP (10045) Operation not supported.

The errors that have User suggestions are all the same ones in the "User-fixable errors" list above. How To Fix Socket Error The protocol family has not been configured into the system or no implementation for it exists. User suggestions: see WSAHOST_NOT_FOUND for details.

Too many links were encountered in translating a pathname.

The missing functions are getprotobyname(), getprotobynumber(), getservbyname(), and getservbyport(). Berkeley description: A bad option or level was specified in a getsockopt()(2) or setsockopt(2) call. For example, the ARPA Internet UDP protocol cannot be specified with a socket type of SOCK_STREAM. Winsock Error 10054 Fix See also: These point to other errors that are similar.

address or port 0). A retry at some time later may be successful. An application attempted an input/output network function call before establishing an association with a remote socket (i.e. http://laptopdeathmatch.com/socket-error/winsock-error-code-10053.php You cannot use more than one WinSock implementation simultaneously.

Shouldn't that be the same size? –Gabriel Sanmartin Feb 22 '12 at 9:06 No, your buffer needs to be big enough to handle any datagram which might arrive. An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full. The current Windows Sockets implementation does not support the Windows Sockets specification version requested by the application. Check the destination address you are using.

WSA_QOS_EFILTERCOUNT 11021 Incorrect QoS filter count. On the server end, you could use a network system utility similar to BSD's "netstat -a" command to check that your server is running, and listening on the right port number. Yes No Additional feedback? 1500 characters remaining Submit Skip this Thank you! On a datastream socket, the connection was reset.

If an application sends a UDP packet to a host/port that does not have a datagram socket "listening," the network system may respond by sending back an ICMP Port Unreachable packet it may occur when a pointer to a structures is invalid or when a value in structure field is invalid). Although the specification doesn't list an error for a function, it does allow for it. An application used a WinSock function which directly maps to a Win32 function.

The WSAGetLastError function returns the last error that occurred for the calling thread. If you are using a host table exclusively, you'll need to update it to add the destination hostname and address. A socket operation encountered a dead host. These two sockets need to work as follows: 1) listeningSocket(non-blocking mode) 2) sendingSocket(blocking mode/dont care) I am trying to send a file thru the "sendingSocket" and recieve the same file thru

WSA_QOS_ESERVICETYPE 11016 QoS service type error. All sockets are created with an associated "address family" (i.e. Errors are listed in alphabetical order by error macro.